仪器网

一. 在线分析总有机碳分析仪 工作原理 Working principle

本仪器采用紫外氧化的原理，将样品中的有机物氧化为二氧化碳，二氧化碳的测试采用的是直接电导率法，通过测试经过氧化反应的样品的总碳含量和未经过氧化反应的样品总无机碳的含量差值来测定总有机碳含量，即：总有机碳（TOC）=总碳（TC）-总无机碳（TIC）。

The instrument adopts the principle of UV oxidation, the oxidation of organic matter in the sample for carbon dioxide, carbon dioxide is tested by direct conductivity method, the total carbon content through the test after oxidation samples and samples without content difference of total inorganic carbon oxidation reaction to the determination of total organic carbon content, namely: Total Organic C (TOC) = total carbon (TC) and total inorganic carbon (TIC).

二. 在线分析总有机碳分析仪 产品特点 Product features

1.仪器采用便携设计，使用轻便，方便移动至取样点。

1. portable design, easy to use, easy to move to the sampling point.

2.采用嵌入式系统，触摸屏设计，纯中文操作方便简易。

2., using embedded system, touch screen design, pure Chinese, easy to operate.

3.针对制药用水（TOC含量在1000ppb以下）总有机碳含量的检测设计，进行检测。

3. for the pharmaceutical water (TOC content below 1000ppb) total organic carbon content of the detection design, testing.

4.配备大量的储存空间，能够存储大量的测试数据。

4. is equipped with a large amount of storage space, can store a large number of test data.

5.中文打印，输出测试参数、测试结果。
5. print in Chinese, output test parameters and test result.

6.在使用、贮存和更换过程中不需要气体或试剂，无移动部件，减少维修和维护成本。

6. in use, storage and replacement process, there is no need for gas or reagents, no moving parts, and less maintenance and maintenance costs.

7.当测试样品浓度超过规定限度，仪器能够自动报警，并输出控制信号。

7. when the concentration of the test sample exceeds the specified limit, the instrument can alarm automatically and output control signals.

8.符合国家2010版《中国药典》规定的测试方案，可以提供 IQ/OQ/PQ 服务。

8., in line with the national 2010 edition of the "Chinese Pharmacopoeia" provisions of the test program, you can provide IQ/OQ/PQ services.

三、 在线分析总有机碳分析仪 技术参数及特点 Technical parameters and characteristics

3.1 主要技术参数 Main technical parameters

电    源 Power supply：220V±22V

电源频率 Power frequency：50Hz±1Hz

额定功率 Rated power：100W

基本尺寸 Basic size：44cm×18cm×26cm

检测极限 Detection limit：0.001mg/L

检测精度 Detection accuracy：±5%

检测范围 Detection range：0.001mg/L～1.000mg/L

分析时间 Analysis time：4min

响应时间 Response time：15 min以内

样品温度 Sample temperature：1-95℃

环境温度 Ambient temperature：10-40℃    温度变化在±5℃/d以内

内部样品流速 Internal sample flow rate：0.5 ml/min

相对湿度 Relative humidity：≤ 85%

重复性误差 Repeatability error：≤ 3%

零点漂移 Zero drift：±5%

量程漂移 Range drift：±5%

3.2 在线分析总有机碳分析仪  特点 ​Characteristic

① 不需要添加酸试剂、氧化剂和任何气体，无需附加日常维护费。

② 操作简单、快捷、可靠。使用者无需专业知识和专门培训。

③ 针对TOC1000ppb以下去离子水的检测设计，在线、离线检测可以切换使用。

④ 超大的存储器能自动存储zui近12个月连续检测的数据，可以查询任意一天的检测记录，并能打印检测结果。

⑤ 检测速度快，一次检测分析时间仅为4分钟。

⑥ 同步检测水样的电导率值，将TOC分析仪与电导率仪合二为一。

⑦ 体积小、重量轻、耗能少、携带方便。

⑧ 具有自动的上限报警输出，超出设定的检测结果时可以提醒操作者。

⑨ 易于按照USP <643>和EP <2.2.44>以及中国药典2005年版附录Ⅷ R所要求的TOC检测方法进行系统适应性验证。

⑩ 超大的320´234的点阵真彩显示器以及人性化的界面，具有RS232数据接口和打印机接口。

There is no need to add acid reagents, oxidants and any gas without additional maintenance costs.
The operation is simple, quick and reliable. Users do not need professional knowledge and specialized training.
For the detection and design of deionized water under TOC1000ppb, on-line and off-line detection can be switched.
Super memory can automatically store the last 12 months of continuous detection of data, you can query any day of the test records, and print the results of the test.
The detection speed is fast, and the analysis time is only 4 minutes at one time.
The simultaneous detection of water conductivity value, TOC analyzer and conductivity meter will be made one.
The small volume, light weight, low energy consumption, easy to carry.
It has automatic limit alarm output, so that the operator can set the test results beyond.
Easy to TOC method in accordance with the requirements of USP <643> and EP <2.2.44> and China Pharmacopoeia 2005 edition appendix VIII of R system to verify.
The large 320 234 dot matrix color display, user-friendly interface, data interface and printer interface with RS232.

四、 在线分析总有机碳分析仪 仪器各部件的安装、连接
开箱后，按以下步骤进行安装：
── 根据装箱单检查仪器是否齐备。
── 确定仪器在运输过程中没有遭到损坏。
── 拆除机箱的外包装，将其置于正确位置 。
── 检查仪器保险丝是否装好，连接市电电缆到接线端子。
── 根据安装图连接进液和出液管路 。
── 系统通电 。

Installation and connection of all parts of the instrument
After unpacking, install as follows:
Check the equipment according to the packing list.
- make sure the instrument is not damaged during transit.
- remove the outer packing of the case and place it in the correct position.
Check that the instrument fuse is fixed and connect the mains cable to the terminal.
Connect the inlet and outlet lines according to the installation drawing.
System electrify.

五、安装

1 安装位置的选择

将仪器放在一个洁净、无障碍物的平面上，并保证除仪器外还能承载 25kg的重量，为了便于散热，请确保仪器的后面和两侧留有至少16cm的空间。

2 电源要求

电压：220V ± 22V

电源频率：50Hz ± 1Hz

3 环境要求

仪器应在一个恒温恒湿且适于工作的环境中进行。避免阳光直射和超常温度；温度过高（超过104°F，40℃）会导致运行失常，温度过低（低于50°F，10℃）会导致测量值误差过大。

install
1 Selection of installation location
Place the instrument on a clean, barrier free surface and guarantee the weight of the 25kg in addition to the instrument. Be sure to leave at least 16cm of space in the back and sides of the instrument for ease of heat dissipation.
2 power requirements
Voltage: 220V + 22V
Power frequency: 50Hz + 1Hz
3 environmental requirements
The instrument should be in a constant temperature and humidity environment suitable for work. Avoid direct sunlight and excessive temperature; the temperature is too high (over 104 degrees F, 40 degrees Celsius) will lead to abnormal operation, the temperature is too low (lower than 50 degrees F, 10 degrees Celsius) will lead to too much error in measurement.

欢迎您选用我公司开发研制的各类检测仪器。在使用过程中，如出现什么问题，可随时和我们，您将得到良好的售后服务。真诚的希望您能将宝贵的意见，丰富的经验和独到的见解反馈给我们！

：  

You are welcome to choose all kinds of testing instruments developed by our company. In the process of use, if any problems, you can contact us at any time, you will get good after-sales service. We sincerely hope that you will give us your valuable advice, experience and insights!
Contact number: :